4 Steps to Install A Napkin Tissue Folding Machine
Did you know ?
Like a table napkin,if 50% of U.S. population used 1 paper napkin per meal three times a day,164,250,000,000(yes billion) napkins would be used over just in 1-year
Napkins are no stranger to everyone, how are napkins produced? That’s right, it’s made by the napkin tissue folding machine. Today, we will talk about how to install a napkin machine.
Steps of installing a Napkin Tissue Folding Machine
- Install the main body of napkin tissue machine & easy
- Install the jumbo roll
- Passing paper through the whole machine
- Open switch test machine
HOW TO INSTALL THE MAIN BODY ?
The napkin machine should be placed on a flat concrete floor, and the base of the machine and the ground should be stabilized with rubber sheets or wooden boards. After the napkin machine is in place, the grounding wire must be added to the machine to prevent the machine from leaking. During the production process, the protective hoods should be kept in good condition; if any paper is found stuck on the embossing roller or the wool roller, it should be cleaned up in time to avoid smashing. The wool roller is also damaged by the napkin machine. Keep the drive or sliding parts of the napkin machine lubricated.Note: As usual, One 40 feet High container can only load 10 tons of jumbo toilet tissue rolls. But If you purchase it from China, The sea freight from China port to your country is very expensive. Thus, It’s not feasible for you to purchase it from China directly.
Installing the ball mill,first install the main bearing:
—In order to avoid aggravation of the wear of the shoulder and bearing lining of the hollow journal, the elevation of the base plate of the two main bearings should not exceed 0.25 mm per meter length.
—In order to avoid aggravation of the wear of the shoulder and bearing lining of the hollow journal, the elevation of the base plate of the two main bearings should not exceed 0.25 mm per meter length.
Second,installing the ball mill:
—Combined with specific conditions, the pre-assembled whole simplified part can be directly installed, or can be installed in several parts, and should check and adjust the center line of the journal and the ball mill, the concentric error must be Guaranteed to be less than 0.25 mm per meter length.
—Combined with specific conditions, the pre-assembled whole simplified part can be directly installed, or can be installed in several parts, and should check and adjust the center line of the journal and the ball mill, the concentric error must be Guaranteed to be less than 0.25 mm per meter length.
Install the transmission parts (small gear, uranium, couplings, reducers, motors, etc.):
— During the installation process, measurements and adjustments should be made in accordance with product technical standards. Check the radial slip of the ring gear and the meshing performance of the pinion; the concentricity of the reducer and pinion; and the concentricity of the motor and reducer. After all installations are satisfactory, the subsequent bolting of the foundation bolt and the main bearing bottom plate can be performed.
— During the installation process, measurements and adjustments should be made in accordance with product technical standards. Check the radial slip of the ring gear and the meshing performance of the pinion; the concentricity of the reducer and pinion; and the concentricity of the motor and reducer. After all installations are satisfactory, the subsequent bolting of the foundation bolt and the main bearing bottom plate can be performed.
HOW TO INSTALL THE JUMBO ROLL?
There are Several Diferent Sizes Of Napkin Machine for producing different sizes final products.Such as
- 230*230mm
- 300*300mm
- 330*330mm
- 400*400mm
You can buy the jumbo roll according to the folding sizes of your final products.And usually,the jumbo roll is installed on the machine by pneumatic lifter,because of its heavy wight.
HOW TO PASS JUMBO ROLL THROUGH THE MACHINE?
Note:Do not smoke in the paper machine factory
After passing the jumbo roll, you can open the switch and use PLC to control the tension of the jumbo roll.
OPEN THE SWITCH TO TEST MACHINE
For support and guidance
If you are going to be a napkin tissue paper business owner you need to have business skills, even more so than technical skills about your product or service.
- Training
It is recommended to get training when joining the toilet paper business industry. There are many essential practical skills which you will need when starting a napkin tissue business.You can get training from your napkin tissue machine supplier when buying the machines, or inviting engineers from supplier factory to come for training in your factory directly.
- Marketing strategies
When your final products are ready for market, You’re the new brand for all customers. As usual, We suggest to buy Napkin Tissue Machine, Facial Tissue Machine, Public Jumbo Roll Machine, Maxi Roll Machine,etc. together with Toilet Paper Machine. In this way, you will have variety finished products in market and esay for customers know who you are.
This industry has large growth potential and is a great business opportunity. napkin tissue has become a basic need all across the world. It can’t be recycled so there is always need for more.
Every single person on the planet uses it on a daily basis. Why shouldn’t you be the one making it and selling it to them?
Now It’s Your Turn
I hoped you enjoyed my detailed information for starting toilet paper business.
Now I want to hear from you:
Which parts from this post are you most excited to know ?
Are you going to know more other kinds of related products? Or do you want to do deep research on this line?
Let me know by leaving a quick comment.
